cnc-club.ru for English speaking users
Nick » 17 окт 2014, 10:23
narvf писал(а):In tecroids image for exmaple path goes down, right, up, right, down, right and so on except for letters so on.
May be it's Spiral vs Zig-Zag option?
-

Nick
- Мастер
-
- Сообщения: 22463
- Зарегистрирован: 23 ноя 2009, 16:45
- Откуда: Gatchina, Saint-Petersburg distr., Russia
- Репутация: 1533
- Заслуга: Developer
- Медальки:
-
tecdroid » 22 окт 2014, 22:15
hi,
i just played around a bit and i think i've found some good working configuration.
However, I've got some questions.
Is it possible to set the zig zag orientation? sometimes it would be easier if it was the other way..
Next, I find it a bit disturbing that my mill pre penetrates any corner of the zig zag about five times before it mills.. can i reduce that number?
-
tecdroid
- Новичок
-
- Сообщения: 25
- Зарегистрирован: 18 июн 2014, 13:35
- Репутация: 1
-
Nick » 28 окт 2014, 11:44
tecdroid писал(а):Is it possible to set the zig zag orientation? sometimes it would be easier if it was the other way..
There should be angle parameter which defines zig-zag "orientation"
tecdroid писал(а): I find it a bit disturbing that my mill pre penetrates any corner of the zig zag about five times before it mills.. can i reduce that number?
What does that mean?
-

Nick
- Мастер
-
- Сообщения: 22463
- Зарегистрирован: 23 ноя 2009, 16:45
- Откуда: Gatchina, Saint-Petersburg distr., Russia
- Репутация: 1533
- Заслуга: Developer
- Медальки:
-
tecdroid » 13 ноя 2014, 00:21
When engraving an area the machine runs a straight line, goes up to safe z, goes down, runs next line and so on..
i'd like it to engrave the whole area and only going to safe position when neccessary..
-
tecdroid
- Новичок
-
- Сообщения: 25
- Зарегистрирован: 18 июн 2014, 13:35
- Репутация: 1
-
narvf » 13 ноя 2014, 02:00
I think it's actually not possible :/
-
narvf
- Кандидат
-
- Сообщения: 60
- Зарегистрирован: 22 июл 2014, 11:39
- Репутация: 4
-
tecdroid » 14 ноя 2014, 12:28
well, should be since it saves much time..
-
tecdroid
- Новичок
-
- Сообщения: 25
- Зарегистрирован: 18 июн 2014, 13:35
- Репутация: 1
-
Вернуться в English forum
Кто сейчас на конференции
Зарегистрированные пользователи: 1240, Bing [Bot], borodaagvali, bypass, Спирт, Dimka_almighty, Evgeny1, EX854508, Gavril, Gestap, Google [Bot], Kovus2, lkbyysq, Majestic-12 [Bot], MGG, nickoass, niksooon, NKS, Гагарин, romanru1, ruh2100, serpvect, spryt, stenkodv, vladi552, vladumur, xenon-alien, Yandex [bot], zakatnyi, ДмитрийП, шпиндель
Поделиться